Field Recording Guide Asbjoern Andersen


How do you prepare for a field recording trip? Recordist and sound designer George Vlad has been on more than a few – from smaller hikes, to flying halfway around the world.

In this in-depth guide, he shares his tips, insights and ideas for planning a successful field recording trip – covering everything from transportation, bags, recorders and microphones, to power, cables, storage and more:


Written by George Vlad

 

Hi, I’m George Vlad and I like to point mics at things. I record all sorts of sounds, from ambiences and wildlife to machinery and aircraft and everything in between. I’ve released a few libraries through Mindful Audio and I often share free recordings on the MA blog.

I’m currently planning a month-long field recording trip to the Carpathian Mountains and the Danube Delta in Romania. As is always the case, I have to go through extensive preparations so that once I get there I can forget everything else and focus on getting the best recordings. Having done this many times in the past, I’m going to go into some detail about how I prepare for a recording trip, from a short hike to flying halfway around the world.

Before I can start preparing for the trip I will first decide what sort of trip it is. I will ask myself questions like “how do I get to where I’m supposed to be recording?”, “what’s my subject?”, “is there a chance I can record something else as well?”, “is there any hiking involved?” etc. The answers to these questions will make my decisions much easier.
 

Transportation

Headlights shine on a Scottish road and into a pitch black night

Night driving in Scotland is awesome

One of the most important points to establish concerns my means of transportation to the place I need to get to. If I have to walk for miles then my gear variety will drastically be reduced. I’m not afraid of a bit of hiking, but lugging gear over long distances is rarely feasible. I don’t want to get to the place I need to be and fall to the ground exhausted. On this type of excursion I will usually stick to my Sony PCM-D100 handheld as my main recorder.
[tweet_box]In-depth guide: How to prepare for a successful field recording trip[/tweet_box] I’m the happiest when I can drive to the place I need to record in, even if there’s a bit of off-roading involved or a little hiking at the end. In this case I’ll take my main rig along, which these days almost always consists of the Sound Devices 633 and my Sennheiser Double Mid-Side rig. This gives me a lot of options (from recording mono to Mid-Side and Double Mid-Side, which then can be decoded to a multitude of formats) and is not that difficult to carry around. On top of the DMS rig I will also bring my Sennheiser MKH-416 just in case I need a bit of reach, plus my DPA 4060s and 4061s for micing up individual sources.

I’m the happiest when I can drive to the place I need to record in, even if there’s a bit of off-roading involved or a little hiking at the end

I will also include a couple of contact mics and hydrophones plus the Sony PCM D100 which is always in my backpack. Of course, recorders and mics have to be powered, connected, supported and protected so I will bring along batteries, cables, stands, blimps and many other extras which I will go into more details about.

An assortment of mics, cords, muffs, and a digital recorder in a bag sit together

Preparing for the Wildeye workshop in Northumberland, May 2016

If flying is involved then my gear will look a bit different. First of all, I have to decide exactly what I need to bring along and drop everything that isn’t necessary. Secondly, I must decide what comes in my backpack and what needs to be checked in. I will normally bring my laptop, recorders and mics on board in my backpack. I will check with each airline so that my bags do not exceed weight and size limits, since rules vary between companies. It’s also useful to check how many batteries I can bring along in my checked baggage, although I’ve never seen these rules enforced.

Occasionally different means of transportation will be involved. Open top cars or boats will not protect from rain, so I will bring rain covers for my backpack, recorder bag and blimp. A Peli case would come in very handy in these situations, but flying with it is problematic since it will attract unwanted attention (from both security and possible thieves). I’ve heard of Peli cases being confiscated by Customs agents in South Africa for example, which resulted in days spent trying to get them back.
 

Bags

A backpack and a bag with a digital recorder sit next to each other

North Face backpack and Kata recorder bag

99% of the times I leave home I will have my backpack with me. This is a showerproof (not waterproof, those are a different form factor and less easy to use) North Face backpack with about 35L of storage volume. It holds my Sony PCM D100 with the Rycote fluffy, a small Manfrotto stand, a Gopro camera, a Nikon DSLR, a portable HDD with a backup of my most important data, a pair of binoculars, headphones, cable/zip ties, tape, cereal or fruit bars and other small bits. I will also grab a bottle of water, thermos flask full of tea or both depending on how long I’ll be out.


Popular on A Sound Effect right now - article continues below:


Trending right now:

  • Cinematic & Trailer Sound Effects Abandoned Oil Tank Play Track 327 sounds included $40

    On a recording trip to the smaller Danish port town Struer, I came across an abandoned empty oil tank. Inside I found two giant wires attached to the floor and the ceiling of the tank, almost like a huge 2 stringed double bass. I’m telling you the reverb in there was longer than the Eiffel Tower on a cloudless day !

    On the outside this was just an empty abandoned building, but it turned out it was not empty at all because it was full of sound and a few dead birds. I’m glad I was curious enough to go inside for a closer investigation and not just pass by.

    After several hours of concentrated recording, it was nice to get my ears back out in dry air. I’m happy there are no open sends to Valhalla in real life but experiencing the eternal resonance on the low frequencies from the wires was absolutely amazing.

    Abandoned Oil Tank was recorded with a LOM basic Ucho stereo pair, a Zoom H6 and the LOM Geofon. All files are in 96 kHz/24 bit and contain the original recordings.

    The result is a unique sound effect library including balloon pop impulse responses from a truly unique location that very recently became even more unique since word says that the oil tank is no more and has abandoned this world.

    327 individual sounds – all tagged with Universal Category System (UCS) metadata.

    www.katrineamsler.com

    20 %
    OFF
    Ends 1713131999
  • Electricity Sound Effects Polarity Play Track 975 sounds included $72

    Polarity delivers more than 950 sounds of electricity, science and technology – captured in several locations around the world, from electricity museums to science labs. About 50% of the library is all about electricity, with various types of Jacob’s Ladders, Tesla Coils, Ruhmkorff lamp and all sorts of impactful bursts of energy.

    Then we go through welders, plasma spheres, 3D printers, starting to cover a more broad technology theme – like old phones, telegraphs, dynamo wheels, rotary dials, whirling watchers, alarm, lab centrifuges, something scientists call a roller and a rocker, servo sounds, neon lights, a wimshurst machine and sparklers.

    Many sounds in this section were captured from vintage equipment, from a 1928’s tram to old telephone switchboards, high voltage levers and control surfaces.

    All content was recorded at 192KHz with a Sanken CO100K, a couple of Sennheiser 8040 and a Neumann 81i, translating into final assets that have plenty of ultrasonic content, ready for the most extreme manipulation.

    Bonus: Two extra libraries included for free:
    This library also includes two additional releases from Mattia Cellotto - for free: Crunch Mode delivers 230 crunchy sounds made with a variety of vegetables, fresh bread, pizza crust and a selection of frozen goods. The Borax Experiment gets you 158 squishy, gory, slimy and gooey sounds.
    20 %
    OFF
  • Door Sound Effects Noisy Doors Play Track 44 sounds included $10

    This library contains recordings of eleven different types of doors specifically chosen for their interesting sound. I performed all actions with a lot of detail covering “open/close”, “knocks”, “bangs and thuds”, “handle grab and rattle” and when possible also “crackles and squeaks” (all recorded at various intensities)

    50 %
    OFF
    Ends 1711666799
  • Metal Sound Effects MetalMotion Play Track 2000+ sounds included, 239 mins total $110

    MetalMotion is a sound design construction kit that contains four hours of moving metal mayhem: clicks and clanks, rolls and drags, wronks and squeals, scrapes and rattles, ranging from from tiny to monstrous. Nathan Moody’s unique performances with unusual combinations of props produce everything from Foley-like movements to intense groans and howls.

    Whether you’re covering a robot’s movements, sweetening weapon Foley, making crafting or pick-up sounds in a game, placing unusual layers beneath a kaiju’s roar, or crushing a submarine with undersea pressure, this collection covers the full range of subtle to raucous. Each file has many performance variations for creative choice and game audio asset creation.

    While there are some tasty impacts within, this library’s true focus is on characterful movements: handling, rummaging, opens, closes, ratchets, swirls, rolls, drags, drops, spins, rubs, zuzzes, and bows. Metal containers, filing cabinets, modern appliances, vintage (and very rusty) tools, cymbals, bells, grills, plates, bars, rods, and tubes, and many other props lent their voices to this collection.

    This UCS-compliant library was recorded with a combination of standard, contact, and ultrasonic-capable microphones through Millennia preamps. Sample rates vary based on the amount of ultrasonic content in each file. The audio files are mastered for realism, ready for extreme processing and pitch shifting of your own, but still useful in more grounded contexts.


Latest releases:

  • Trench Rammers is a one-of-a-kind sound library, created by sound designer Barney Oram. It features recordings of two 20th century Trench Rammers, some of the last operating machines of their kind in the world. The library features 48 files in total, capturing the Trench Rammers using a variety of microphones and perspectives, supplied in 192kHz 24bit WAV file format.

    This library contains multiple recordings of two antique Trench Rammers, the Pegson ER5 and the Warsop Benjo, and also features additional recordings of four antique stationary engines, the Amanco Hired Man (1920s), the JAP 1947, the Lister D (1940s) and the Norman T3000.

    Recorded in Leeds, UK, this library features multi-mic coverage and a range of distance positions captured on all included source content. Microphones used include; Sanken, Sennheiser, Neumann and DPA, captured with Sound Devices and Tascam recorders.

    This library includes detailed SoundMiner metadata and utilizes the UCS system for ease of integration into your library.

    Behind the Scenes Video:


    Trench Rammer


  • The cozy natural rhythms of hums, scrapes, splashes and thuds soundtrack the pottery workshop where the earth meets art. Find the true sound of it with Vadi Sound Library.

     

    About Pottery Workshop

     

    84 sounds that are clean, subtle and capture pretty much every object and action of the magic of fire and earth.

    From the rhythmic hum of the spinning potter’s wheel, to the splash of water, the scrape of clay with the tools shaping and smoothing surfaces, listen up for the symphony of creation.

    You will hear the tapping and thud of ceramic pottery, wooden ribs, wire cutters, loop tools, and sponges, all kinds of rummage, and mud actions on the potter’s wheel. The clicking and whirring of mechanisms during firing cycles add a mechanical counterpoint to the workshop’s natural rhythms.

    You will get variations of sounds in different proximity, size, and style of action. This collection is handy due to the clarity and diversity of the raw sounds. They have both Foley and practical usability and room for further sound design.

    You will get intuitive, detailed naming, UCS compatibility and the usual Vadi Sound craft and attention to detail in 84 pristine sounds. Recorded in 24bit-96kHz.WAV format on our favorite Sennheiser MKH 8040 stereo pair and Zoom F6.

     

    Keywords

    Pottery, workshop, electric potter’s wheel, wheel, oven, heat gun, mud, clay, ceramic, glass, wooden, metal, cup, handle, push, pull, move, remove, shape, tap, shake, clank, level, lid, tool, organizer, toolbox, rummage, fiberboard, button, bucket, sponge, plate, Dremel.

     

    What else you may need

    You may also want to check out Drag & Slide for 477 sound files of dragging, sliding, scraping and friction sounds of different objects made of wood, plastic, metal on various surfaces. Our bestseller Crafting & Survival is another good choice to get access to 1000+ survival, gathering, movement and crafting sounds.

  • All files are recorded 32bit, 192 kHz, with Shure KSM 137, Line Audio Omni1, FEL Clippy XLR EM272, Sonorous Objects SO.3 and JrF C-Series Pro+ microphones, Sound Devices MixPre-6 II & Zoom F3 recorders. Library contains wav files of driving, interior and exterior foley, mechanical and electrical sounds. It is also available in UCS.

  • Introducing Devils Bane Trailer, a chilling symphony of horror encapsulated in 533 meticulously crafted sound files, ready to unleash terror upon your audience. Dive into a nightmare realm where every creak, whisper, and shriek is meticulously designed to send shivers down your spine.

    • 533 files
    • 3.5 GB of game audio assets
    • All in 96k 24bit .wav
    • Dark Horror Movie Trailer Sound Effects Library
    17 %
    OFF
  • Birdsong from the countryside of the Swedish rural region of Värmland.

Need specific sound effects? Try a search below:


I carry my recorder in a Kata bag along with a few cables, cable ties, a knife, a pair of DPA 4060s or 4061s, contact mics, electrical tape, head torch and a few other knick-knacks. I will occasionally bring an extra mixer as well (a Sound Devices 302 or Mixpre-D) if needed since there’s enough room for it in there. I tried using smaller bags such as the ones made by Petrol or Orca, but these did not suit me since I don’t do a lot of run-and-gun high-speed action. Having extra space for cables and mics proved much more useful on the type of recording trips I do so I opted for the larger Kata bag in the end.

When I fly, I use softshell wheeled suitcases made by Eastpak or Timberland. These will not attract as much attention to themselves as a Peli or similar case will do, are relatively spacious and are less prone to cracking than hard-shell luggage. This means they can be compressed to some degree though, so I take extra care when packing so that delicate items have an extra layer of protection. I will occasionally wrap the suitcases in cling foil so that they are held together tightly.

Mics and recorders covered with wet weather gear sit in a damp forest

Taking a break until the rain subsides

I mentioned dry bags for covering gear and bags in a pinch. Before leaving on the South Africa trip last year I purchased an assortment of Karrimor Dry Bags which proved very useful when a sudden downpour caught me in the bush away from shelter. I was able to cover my Cinela blimp and my recorder bag so that they did not get wet even though it was raining heavily. The dry bags came in very handy on my trip to the Danube Delta where we had to travel by boat for long distances every day.

There are good Samaritans, even if one might be inclined to think otherwise, so I try to make it easy for them to help me if they accidentally find any of my stuff

One minor aspect that can make a huge difference is tagging all my bags and gear in case anything gets lost or misplaced. There are good Samaritans, even if one might be inclined to think otherwise, so I try to make it easy for them to help me if they accidentally find any of my stuff.
 

Recorders and microphones

A wind screen, cords, headphones, and a box with a condenser mic sit together

Cinela blimp with Sennheiser MKH30 and 7 pin XLR breakout lead

Probably the most important bits of my kit, recorders and microphones require special consideration before going on a field recording trip. I take my Sony PCM D100 with me all the time since it’s light and handy and it sounds excellent. Whether I use it as backup, extra or main recorder, I’m sure I’ll get great results that I can use in my work or share as sound effects libraries. If I need to use external microphones I can combine it with a field mixer, but this option limits me to 2-channel recording.

Fruits of the labor: Sound libraries by George Vlad:

George Vlad has released several sound libraries on his own, and in collaboration with fellow recordist Daan Hendriks – a few examples (more here):

  • Nature & Countryside Ambiences Southern African Ambience Play Track 56/112 sounds included, 330 mins total From: $100

    Southern African Ambience is a collection of rich and immersive savanna ambiences, recorded by George Vlad and Daan Hendriks in the north of South Africa, just on the border with Botswana.

    Library highlights:• Lush ambiences, each over 4 minutes and up to 10 minutes in length, in stereo and surround
    • Huge amount of birds, with 45 species identified in metadata
    • Mammals such as Baboon, Bushbuck and Black-backed Jackal
    • Crickets, cicadas, flies and frogs
    Download the surround demo wav here

    Excerpts from The Audio Spotlight’s review:
    “The quality of the recorded sounds is phenomenal”
    “A special mention goes to the Baboons which are scary as hell”
    “The birds are fantastic”

    – read the full review of Southern African Ambience here

  • Environments & Ambiences Woodland Atmosphere Play Track 58+ sounds included, 309 mins total $110

    Woodland Atmosphere is a collection of clean and immersive natural ambiences recorded in forests around Europe by George Vlad. The library is updated with new content on a regular basis, all free for existing users.

    Get more than 5 hours of pristine nature recordings and birdsong with this SFX library:

 

3 is the magical number when it comes to preamps as it allows me to record Double Mid-Side without needing an extra mixer

If I want a more compact solution than the D100 plus mixer, or if I need more than 2 channels, I will take my Sound Devices 633 mixer/recorder. I’ve had it for about three years and I think it’s simply an amazing piece of kit. I’ve used it without any problem in temperatures ranging from -25 to 40 degrees Celsius (that’s -15 to over 100 degrees Fahrenheit). Its preamps and limiters are excellent, it allows for a variety of powering options and it’s quite intuitive to use. Also, 3 is the magical number when it comes to preamps as it allows me to record Double Mid-Side without needing an extra mixer.

A mic sits in a bushy plain on a cloudless day

Recording the sounds of the African savanna

Once I’ve decided on what recorder to bring, it’s time to think about microphones. If I need to record ambiences, I’ll take my Sennheiser Double Mid-Side rig made up of two MKH-8040 mics and one MKH-30. These are housed in a custom-made Cinela blimp that outputs to 7-pin XLR, which comes with a hard plastic shell that’s very convenient to use when flying. One thing to keep in mind here is that I will not travel with the mics mounted in the blimp, as they MKH30 is quite heavy and the whole unit might break under the weight. I prefer to take the mics in my backpack and only mount them once I’m on location.

Alternately I can use the 8040s with Rycote Extended Ballgags (also called WS 9) mounted on an ORTF stereo bar. This will yield great results for ambience, although I prefer the versatility of the DMS rig.

I will not travel with the mics mounted in the blimp, as they MKH30 is quite heavy and the whole unit might break under the weight

If I need to record point sources I will generally choose my Sennheiser MKH-416 which sounds excellent on vehicles, firearms, engines, mechanical sources, fireworks, you name it. I can also use my MKH-8040s for mono recording, and for this purpose I can separate the two Rycote XBGs and point them at sources individually. One other option is using lav mics, of which I have 4. I use DPA 4060 lavs for micing up bird songposts or nests, since they’re so tiny and difficult to spot. In a pinch I have also used them for recording vehicles, but I prefer to use the DPA 4061s for this purpose since they’re a bit less “hot” and can therefore withstand louder sound sources.

I will occasionally use other mics such as the Crown PCC, JrF contact mics and hydrophones, Line Audio CM3s, AKG D112, Shure SM58s etc. I’ll probably not use these as my main mic, but they’re excellent as additional mics that provide a different tone or perspective.
 

Power

A bunch of batteries and battery charges sit in a pile

I got the power!

I always keep my batteries charged in case I need to go out and record something on a short notice. I use a whole bunch of Sanyo Eneloop AAs (both 1900 and 2500 mAh) since they’re high capacity, rechargeable (easy on the environment), hold their charge for a long time and aren’t too expensive. I will take about 20 of these if luggage permits it and I’ll use them with the D100, torches, walkie talkies etc. It’s also worth investing in a smart charger for AA and AAA batteries.

The sound Devices 633 takes 3 types of powering. One is 6xAA batteries which works as a backup option, but isn’t sustainable since a set only lasts for about an hour or so. Another option is 7.4V Sony L-type batteries, which I use. I have two IDX batteries that allow for more than 10 hours of continuous recording, phantom power included. A third option is an external battery pack connected via a 4-pin Hirose connection. I haven’t needed this so far but I think I’ll consider it if I want to incorporate another mixer into my rig in the near future.

Airlines have regulations in place regarding the total capacity of carried batteries so I normally check this before flying with a whole bunch of rechargeables

I also tend to carry along a powerbank that I use to recharge phones, tablets and even my laptop. This comes in handy on extended trips or in places where access to electricity is scarce or unavailable. It will pair with solar charging panels very well.

As mentioned already, airlines have regulations in place regarding the total capacity of carried batteries so I normally check this before flying with a whole bunch of rechargeables. It’s also worth noting that batteries should be insulated from contact with one another, otherwise they can start fires. There are plastic cases for AA or AAA batteries available for very cheap, so there’s no excuse for storing batteries willy-nilly.
 

Cables

Roughly a dozen cables sit in a pile

It’s not always possible to coil cables properly, but I try.

I used to get the cheapest cables I could find. I don’t work in environments where interference is an issue and my gear is almost never plugged in while recording, so I figured I’d be fine. It turns out interference is not the only problem that cables can cause. They can also peel off or break if used outside, but the worst is when they simply stop working without any apparent cause.

I had my first cheap cable die on me when I was out recording a WW2 training prop plane with a couple of friends. The cable just stopped working when I was setting up my equipment, exactly as the pilot /owner was taking the plane out of the hangar. It had been working the night before when I tested everything. It wasn’t broken or torn, but somehow it was not connecting my mic to the recorder.

Fortunately, I was carrying plenty of spares so I quickly ran to the car and got another cable. This one worked and so we were able to record the plane in all its glory. After I got home I checked the cable once again and it still didn’t work, so I got rid of it and a few other cheap cables I had lying around. I decided I’d only purchase higher quality cables from then on, and never had a similar problem since.

The cable just stopped working when I was setting up my equipment, exactly as the pilot / owner was taking the plane out of the hangar

3-pin XLR cables are quite easy to find. I either get Van Damme cables off Amazon or Pro Sound cables from Maplin. These are very useful for single source recordings at any length. I have used 100m cables with no apparent quality issue.
Chris Watson mentioned using 250m long XLR cables on one of the Wildeye trips, so length is not a problem.

When recording ambiences in stereo or DMS, I will use 5 or 7-pin XLR audio cables coupled with breakout leads. These are difficult to find and generally more expensive, but are much easier to use when having to lay long cables in forests, wetlands, savanna etc. I normally have mine custom made by Wendy’s Broadcast or Canford here in the UK, and I shop around before buying as prices vary wildly.
 

Storage

Towers and hard drives sit on the floor

For a long time I’ve only been using Sandisk SD and CF cards in all my devices. Sandisk Extreme Pro memory is excellent for recording more than 2 tracks at 192 kHz or for fully taking advantage of the buffer on DSLRs. I have about 10 of these at any time so if any fails I can always replace it easily, although none has failed as of yet (knock on wood).

One useful feature of the Sound Devices 633 is that it records simultaneously to CF and SD card so if any of them fails the recordings aren’t lost. I also try to transfer everything from the recorder to my laptop and portable HDDs as soon as I’m back from a recording trip. Once this is done I format all cards so that they’re ready to be used again.

I will take a couple of 4TB portable hard drives with me when I’m on a lengthy trip. I store my sound effects library and work files on these in case I need to get any work done while away from the studio (which happens more often than expected). I will also back up my recordings onto one of these drives and on the internal SSD of my laptop.

One useful feature of the Sound Devices 633 is that it records simultaneously to CF and SD card so if any of them fails the recordings aren’t lost

Since I mentioned backups, as part of preparing for leaving my studio for more than a few days, I will also take precautions with regards to backing up all my data. I normally set up my Synology DiskStation so that it backs up everything on my workstation once a week. When preparing for a longer trip I will also copy most of the sensitive data to one of my 4TB drives and I will take my Synology DiskStation to a friend’s house. This way I will have my data in at least 3 different places. (I’m looking into backing everything up to the cloud as well, but haven’t decided on a solution yet).
 

Other stuff

It’s easy to forget about smaller, less important bits when preparing for a field recording trip. I have to admit that a few short recording trips have been ruined because I forgot to bring things like headphone adapter or mic stand thread adapter.

It’s also useful to have spare bits of kit for backup, in case something breaks or is lost. I always take two pairs of headphones (Sennheiser HD 25 and HD 26), one in my backpack and the other in my recorder bag. I will carry as many spare cables and breakout leads as I can take.

I have several different Manfrotto stands, normally used for photography or lighting. I take several thread adapters with me so I can use the stands with whatever device or blimp I need. I also got an Ambient boompole that folds down to half a metre so I can fit it in a regular travel suitcase. This doesn’t get a lot of use but it’s very light so it’s easy to include with the rest of the luggage.

A dark figure sites on top of the highest tree branch

African Fish Eagle or Plastic Bag? Shot with Samsung Galaxy S7

I mentioned binoculars and cameras. As sound recordists we are less concerned with the visual side of things, but I find that that’s a very limiting approach. When recording wildlife it’s very useful to know what species I’m recording, and visually identifying them is often easier than by using sound alone. I also like to document my field recording trips, and for this purpose I will use my smartphone camera and my GoPro.

Being able to photograph my subjects is even better since then I can share images and ask for opinions, but this opens another can of worms: photography. I recently got a Nikon D7200 and a telephoto lens for exactly this purpose. The learning curve is steep but it’s very rewarding to be able to pair up my recordings with photos or even footage of what I’m recording.

A plane flies in the sky

Clearly some kind of means of transportation. Shot with Nikon D7200 and 70-300 lens

If I need to record any kind of wildlife I will try to bring camo or at least neutral colored clothing. This means most of my clothes are khaki, dark green or brown. This doesn’t fool wildlife, but it will let me get closer than if I’d be wearing weird colors. I will also use camouflage scrim to hide my mics. As soon as I started using this I noticed that birds would get much closer to my rig than before, so it definitely makes a difference.

If I need to record any kind of wildlife I will try to bring camo or at least neutral colored clothing

If I need to coordinate with others I will bring a couple of Motorola T92 walkie talkies. These come in very handy when traveling in a convoy or on vehicle recording sessions. This model is easy to set up and use and also floats when dropped in water.

There are always a few different kinds of tape in my bag. Electrician’s tape is excellent for taping regular and contact mics to things. Gaffer or duct tape is good for taping mics to vehicles, although it’s not all equal. Some will leave a sticky residue while others won’t, so I normally test it before using it. I will also use zip ties and rope for the same purpose.

Water bottles, thermos flasks and fruit/cereal bars are always useful to have on a trip. If I’ll be out for more than a few hours I’ll generally plan ahead and get lunch or dinner as well.

Besides backing up my data before leaving on a field recording trip, I will research what I’ll be recording. If it’s a vehicle or an object I’ll look it up on the internet and try to learn about it, so I won’t be completely in the dark. If it’s a location I’ve never been before, I’ll educate myself about it. Book series like Lonely Planet and Rough Guides are excellent for getting a general overview of the location.

Books about birds from South America, Europe and Australia

I will also try to find detailed wildlife guides and I’ll look up places on the Xeno Canto website. I stopped making lists of target species a while ago since it’s awfully difficult to control this aspect, but it’s always useful to know what can be encountered in a specific environment.

If I travel to remote places where certain illnesses might be an issue, I will visit a Travel Clinic a month or two in advance so I can get inoculated. These vaccines take several shots before they’re activated so I’d rather do this well in advance so I can avoid any last minute stress.

Like backup, insurance is always good to have, but when going on a field recording trip it’s essential. Flying with gear is problematic as luggage is lost or misplaced all the time. Taking microphones and recorders out into the field introduces variables that can’t always be controlled. For these and many other reasons I ensure my gear with a company that specializes in photography and film equipment insurance. I haven’t needed to make a claim yet but I feel the peace of mind that it gives me is worth the price.

For me, peace of mind is of the utmost importance when I’m out on a field recording trip

On top of insuring my gear, I also take travel insurance and car hire excess insurance. These two aren’t as expensive as gear insurance but they’re easy to forget when preparing for a trip.
 

Weather

One last thing I want to touch on is weather. It’s difficult to predict what the weather will be like months in advance when preparing for long trips. For example, I spent the entire month of April this year traveling and recording in Romania. While there were a few calm and sunny days, I also encountered blizzards and knee deep snow (towards the end of April!), storms that lasted for days and very annoying high winds. It was a mixed bag overall, but it made those few still days even more enjoyable.
At any rate, I stopped being concerned about weather a long time ago. I do my research before planning a trip and then I don’t think about it anymore. Most of the times it works, other times I spend half of my time on a trip recording wind and rain or watching Netflix in a guesthouse. Apps like BBC weather or AccuWeather help but are only reliable short term. Their wind speed estimates are usually spot on, which I find very useful when going out to record ambience.
 

Conclusion

I hope I didn’t manage to turn the idea of field recording preparations from a joyous event to a tedious process. I know people who skip many of these steps and hope for the best. Sometimes it works, most of the times it doesn’t. For me, peace of mind is of the utmost importance when I’m out on a field recording trip. I want to be sure I can rely on my gear and I want to be in control as much as possible. There’s plenty of factors that I’ll never be able to control, and that’s fine as long as everything else has been taken care of. Happy recording!



George Vlad - Field Recording with Telinga


A big thanks to George Vlad for sharing his experiences!

 

About George Vlad:
George Vlad has been fascinated with sound and the great outdoors ever since early childhood. He is based in the UK and works as a freelance games sound designer. When he’s not in the studio George does a lot of traveling, hiking and field recording. You can read more about his trips on his blog
 

Please share this:


 



 
 
THE WORLD’S EASIEST WAY TO GET INDEPENDENT SOUND EFFECTS:
 
A Sound Effect gives you easy access to an absolutely huge sound effects catalog from a myriad of independent sound creators, all covered by one license agreement - a few highlights:

  • Door Sound Effects Noisy Doors Play Track 44 sounds included $10

    This library contains recordings of eleven different types of doors specifically chosen for their interesting sound. I performed all actions with a lot of detail covering “open/close”, “knocks”, “bangs and thuds”, “handle grab and rattle” and when possible also “crackles and squeaks” (all recorded at various intensities)

    50 %
    OFF
    Ends 1711666799
  • Metal Sound Effects MetalMotion Play Track 2000+ sounds included, 239 mins total $110

    MetalMotion is a sound design construction kit that contains four hours of moving metal mayhem: clicks and clanks, rolls and drags, wronks and squeals, scrapes and rattles, ranging from from tiny to monstrous. Nathan Moody’s unique performances with unusual combinations of props produce everything from Foley-like movements to intense groans and howls.

    Whether you’re covering a robot’s movements, sweetening weapon Foley, making crafting or pick-up sounds in a game, placing unusual layers beneath a kaiju’s roar, or crushing a submarine with undersea pressure, this collection covers the full range of subtle to raucous. Each file has many performance variations for creative choice and game audio asset creation.

    While there are some tasty impacts within, this library’s true focus is on characterful movements: handling, rummaging, opens, closes, ratchets, swirls, rolls, drags, drops, spins, rubs, zuzzes, and bows. Metal containers, filing cabinets, modern appliances, vintage (and very rusty) tools, cymbals, bells, grills, plates, bars, rods, and tubes, and many other props lent their voices to this collection.

    This UCS-compliant library was recorded with a combination of standard, contact, and ultrasonic-capable microphones through Millennia preamps. Sample rates vary based on the amount of ultrasonic content in each file. The audio files are mastered for realism, ready for extreme processing and pitch shifting of your own, but still useful in more grounded contexts.

  • Electricity Sound Effects Polarity Play Track 975 sounds included $72

    Polarity delivers more than 950 sounds of electricity, science and technology – captured in several locations around the world, from electricity museums to science labs. About 50% of the library is all about electricity, with various types of Jacob’s Ladders, Tesla Coils, Ruhmkorff lamp and all sorts of impactful bursts of energy.

    Then we go through welders, plasma spheres, 3D printers, starting to cover a more broad technology theme – like old phones, telegraphs, dynamo wheels, rotary dials, whirling watchers, alarm, lab centrifuges, something scientists call a roller and a rocker, servo sounds, neon lights, a wimshurst machine and sparklers.

    Many sounds in this section were captured from vintage equipment, from a 1928’s tram to old telephone switchboards, high voltage levers and control surfaces.

    All content was recorded at 192KHz with a Sanken CO100K, a couple of Sennheiser 8040 and a Neumann 81i, translating into final assets that have plenty of ultrasonic content, ready for the most extreme manipulation.

    Bonus: Two extra libraries included for free:
    This library also includes two additional releases from Mattia Cellotto - for free: Crunch Mode delivers 230 crunchy sounds made with a variety of vegetables, fresh bread, pizza crust and a selection of frozen goods. The Borax Experiment gets you 158 squishy, gory, slimy and gooey sounds.
    20 %
    OFF
Explore the full, unique collection here

Latest sound effects libraries:
 
  • Trench Rammers is a one-of-a-kind sound library, created by sound designer Barney Oram. It features recordings of two 20th century Trench Rammers, some of the last operating machines of their kind in the world. The library features 48 files in total, capturing the Trench Rammers using a variety of microphones and perspectives, supplied in 192kHz 24bit WAV file format.

    This library contains multiple recordings of two antique Trench Rammers, the Pegson ER5 and the Warsop Benjo, and also features additional recordings of four antique stationary engines, the Amanco Hired Man (1920s), the JAP 1947, the Lister D (1940s) and the Norman T3000.

    Recorded in Leeds, UK, this library features multi-mic coverage and a range of distance positions captured on all included source content. Microphones used include; Sanken, Sennheiser, Neumann and DPA, captured with Sound Devices and Tascam recorders.

    This library includes detailed SoundMiner metadata and utilizes the UCS system for ease of integration into your library.

    Behind the Scenes Video:


    Trench Rammer


  • The cozy natural rhythms of hums, scrapes, splashes and thuds soundtrack the pottery workshop where the earth meets art. Find the true sound of it with Vadi Sound Library.

     

    About Pottery Workshop

     

    84 sounds that are clean, subtle and capture pretty much every object and action of the magic of fire and earth.

    From the rhythmic hum of the spinning potter’s wheel, to the splash of water, the scrape of clay with the tools shaping and smoothing surfaces, listen up for the symphony of creation.

    You will hear the tapping and thud of ceramic pottery, wooden ribs, wire cutters, loop tools, and sponges, all kinds of rummage, and mud actions on the potter’s wheel. The clicking and whirring of mechanisms during firing cycles add a mechanical counterpoint to the workshop’s natural rhythms.

    You will get variations of sounds in different proximity, size, and style of action. This collection is handy due to the clarity and diversity of the raw sounds. They have both Foley and practical usability and room for further sound design.

    You will get intuitive, detailed naming, UCS compatibility and the usual Vadi Sound craft and attention to detail in 84 pristine sounds. Recorded in 24bit-96kHz.WAV format on our favorite Sennheiser MKH 8040 stereo pair and Zoom F6.

     

    Keywords

    Pottery, workshop, electric potter’s wheel, wheel, oven, heat gun, mud, clay, ceramic, glass, wooden, metal, cup, handle, push, pull, move, remove, shape, tap, shake, clank, level, lid, tool, organizer, toolbox, rummage, fiberboard, button, bucket, sponge, plate, Dremel.

     

    What else you may need

    You may also want to check out Drag & Slide for 477 sound files of dragging, sliding, scraping and friction sounds of different objects made of wood, plastic, metal on various surfaces. Our bestseller Crafting & Survival is another good choice to get access to 1000+ survival, gathering, movement and crafting sounds.

  • All files are recorded 32bit, 192 kHz, with Shure KSM 137, Line Audio Omni1, FEL Clippy XLR EM272, Sonorous Objects SO.3 and JrF C-Series Pro+ microphones, Sound Devices MixPre-6 II & Zoom F3 recorders. Library contains wav files of driving, interior and exterior foley, mechanical and electrical sounds. It is also available in UCS.

  • Introducing Devils Bane Trailer, a chilling symphony of horror encapsulated in 533 meticulously crafted sound files, ready to unleash terror upon your audience. Dive into a nightmare realm where every creak, whisper, and shriek is meticulously designed to send shivers down your spine.

    • 533 files
    • 3.5 GB of game audio assets
    • All in 96k 24bit .wav
    • Dark Horror Movie Trailer Sound Effects Library
    17 %
    OFF
  • Birdsong from the countryside of the Swedish rural region of Värmland.


     

3 thoughts on “Recording Adventures: Preparing for a successful field recording trip

  1. Excellent article George, thanks for writing this out!
    One question: Which microphone would you choose for stereo ambience recording if you could only pick one?

  2. Thanks Chip, glad to hear you liked it.

    My first choice for stereo ambience would be a pair of MKH-8020 mics in a SASS enclosure. It sounds incredibly rich and open while preserving a lot of detail. I prefer it over a pair of MKH-8040s in ORTF. It can also be upmixed to decent surround.

    I know that’s technically two mics and not one, but I never liked the sound of stereo or MS mics for ambience. Hope this helps.

    George

Leave a Reply

Your email address will not be published. Required fields are marked *

HTML tags are not allowed.